Well Test Config - Headers Page

Well Test > Configuring CygNet Well Test > Configuring Well Test Using Canvas > Headers Page

Headers Page

The Headers page of the well test configuration control defines the list of headers included in each well test configuration. Each header corresponds to a separator facility, and this is where you define its point tag, properties, and the associated wells. The page consists of the following sections:

Headers
Properties
Wells

Click the following image for more information:

Sample Headers Page Configuration

To configure Well Test Headers

Perform the following steps to configure the headers properties, referring to the property definitions below:

Click the Headers tab on the left side of the screen.
Click to Add header or click on previously configured header.
Configure the Enabled check box and Template to be used with this header.
Click to Add well or click on previously configured well.
Click to Enable the well and add the Enabled UDC.
Save any changes.
Click the Templates tab on the left side of the screen to continue well test configuration.

Headers

The Headers section of the Headers page defines the headers to be included in each well test operation.

Property	Description	XML
Tag	Specifies the fully qualified facility tag of the well test header facility in the format: site.service::facility_id.	tag
Add header	Click to select a facility tag for the new header.
Delete header	Click to delete a selected header, as necessary.

Note: Filter column The columns in the Headers grid can be filtered.

Properties

The Properties section of the Headers page defines the general properties of each header included in the well test operation.

Property	Description	XML
Tag	Specifies the fully qualified facility tag of the well test header facility in the format: site.service::facility_id.	tag
Description	Specifies the description of the well test header facility retrieved from the Facility service.
Enabled	Indicates whether the header is enabled. Options include True or False.	enabled
Template	Specifies the name of the header template to use for this header, which must match a defined header template name. The header template name, type, queue UDC, valve positions, and related commands are defined in the <HeaderTemplate> element. More than one header can use the same template.	template

Wells

The Wells section of the Headers page defines the wells associated with each header. Each well is associated with a facility tag and position number. Only enabled wells will be tested.

Property	Description	XML
Position	Specifies the position number for the well. This must line up with one of the positions in the associated header template. Values include 1, 2, 3, …, n.	position
Description	Specifies the description of the well facility retrieved from the Facility service.
Tag	Specifies the fully qualified facility tag of the well in the format: site.service::facility_id. E.g., MYSITE.UIS::AMANDA_WL.	tag
Enabled	Specifies whether the well can be tested. While it is possible for the header queue to contain wells that are disabled, only enabled wells will be tested. When a well is read from the top of the header queue, prior to testing, the enabled attribute will be read. If the well is enabled (True), the associated well command and actions will be processed If the well is not enabled (False), the well will not be tested and the next well in the queue will be evaluated Note: Make sure you read the definition for the enabledUdc attribute for further usage notes on the enabled attribute. Options include True or False.	enabled
Enabled UDC	The Enabled UDC property (enabledUdc) allows the configuration of the Enabled (enabled) property by point. The defined UDC will be combined with the facility tag to formulate a point. The Enabled UDC Property /enabledUdc attribute takes precedence over the Enabled (enabled). Click the browse button to open the Select UDC dialog box and select an appropriate UDC. If that point exists and has a valid value (either True or False), then that value is used to determine the enabled status. If the point doesn’t exist or the value is invalid, then the enabled attribute value will be used. If in this case, the enabled attribute is not configured, and it will be assumed that the well is not enabled. Note: This attribute allows manipulation of a well's enabled/disabled status external to the Canvas Well Test Status screen, and the CygNet Well Test Module.	enabledUdc
Add well	Click to select a facility tag for the new well in this header.
Delete well	Click to delete a selected well, as necessary.

Note: Filter column The columns in the Wells grid can be filtered.