Accesses the Select Service dialog box to select a UIS Site.Service

Lists recently selected Site.Service options. Click to select.

Exits the Dynagraph Viewer.

Accesses a dialog box for selecting a facility in the current UIS.

Selects the next facility in the current UIS (facility order is alphabetical by facility ID).

Selects the previous facility in the current UIS (facility order is alphabetical by facility ID).

Accesses the Select Data Group dialog box, allowing you to select a data group from the list of all data groups configured for the device.

Accesses the Select Command to Execute dialog box, allowing you to select a command from the list of all available commands.

Gets status data to display in the details panel.

Gets pumpoff configuration data from the device.

Gets the fluid fill setpoint from the device.

Gets the current dynagraph card from the device.

See Card Types.

Gets the shutdown card from the device.

See Card Types.

Gets the pump-up card from the device.

See Card Types.

Gets a shutdown card and a pump-up card.

See Card Types.

Gets a reference card for the device.

See Card Types.

Gets the start card from the device.

See Card Types.

Gets an alarm card for the device.

See Card Types.

Gets a failure card for the device.

See Card Types.

Accesses the Request Current Cards dialog box to define a card set to request.

Accesses the Request Shutdown Cards dialog box to define a card set to request.

Submits a Pumpup Card request.

Submits an Alarm Card request.

Submits a Failure Card request.

Submits a Shutdown Card and a Pumpup Card request.

Sends the pumpoff configuration to the device.

Sends the fluid fill setpoint to the device.

Starts a Card Trace.

See Card Requests.

Accesses the Card Trace Setup dialog box to set up a card trace.

See Card Requests.

Aborts the current poll.

See Card Requests.

Aborts the current poll plus polls in the queue

See Card Requests.

Displays the last poll error.

Clears the last poll error.

Accesses the Pump-Off Configuration dialog box to edit values and send the edits back to the RTU.

Accesses the Fluid Fill Setpoint (%) dialog box to edit load and position values and send the edits back to the RTU.

Refreshes the status data display.

Refreshes the pumpoff config display.

Refreshes the fluid fill setpoint display.

The RefreshCards method enables you to manually refresh card data and display to see the latest changes. Useful when a dynagraph card depends on another system for calculations, which might create a small lag time in communication between the systems.

Accesses the Status Point Automatic Refresh dialog box to disable/enable and set a refresh rate (in seconds) for status points.

Enables you to set up a time interval by which to automatically refresh card data and display to see the latest changes.

Useful when a dynagraph card depends on another system for calculations, which might create a small lag time in communication between the systems.

Hide or Show the toolbar.

Hide or Show the status bar.

Select/clear display of the details panel.

Select/clear display of the mark points along the plot.

Select/clear display of the net stroke value.

Select/clear display of the fluid fill setpoint, if applicable.

Accesses the Initial Cards dialog box to select/clear display of previously retrieved cards when navigating to a new device.

Overlays card views within the current view set.

Clears the current view set.

Accesses the Choose Cards to View dialog box, displaying all stored card transactions, allowing you to select a set to display.

Accesses the Enter Value dialog box to select the maximum number of cards to display. Valid values are 5 - 50.

Displays a card plot for surface cards only.

Displays a card plot for downhole cards only.

Displays card plots for both surface and downhole cards.

Enables you to filter downhole cards based on relevant calculation type(s) used in a single transaction. Options only appear if they are valid for the specified transaction.

Options are as follows:

• Device
• Everett-Jennings
• Gibbs

Check only those options you want to display. Graphs for selected card options overlay.

Click Clear Filters to remove any filtering applied. This results in the display of all available card types.

Opens a print dialog box to select parameters for printing the current card and status information.

The ShowCardDetails method displays the Dynagraph Card Details dialog box, displaying card information and position/load pairs.

The SaveReferenceCard method displays the Save as Reference Card dialog box, allowing you to save the selected card as the most recent reference card in your CygNet system.

Displays options for exporting the card to a text or data file.

Deletes the card.

Moves to the next card in the view set.

Moves to the previous card in the view set.

Displays an About CygNet Dynagraph Viewer Application dialog box to view application information.

Available information includes the following:

• The application name, version, and release date
• Copyright information
• The CygNet Software website address, including a hyperlink to the website
• The log file location, including a hyperlink to the log file
• The location of the application's file executable

In addition to information about the application, the About box includes the following buttons:

• Client Settings — opens the Client Settings dialog box to view and modify client log settings for the application on an ad hoc basis. See Client Log Settings in the Logging section for more information.
• Diagnostics — access the following options for additional analysis from the drop-down menu:

• Loaded Modules — use this option to view and search file information for modules loaded in your system. Double-click any result row to view properties for that module. See Loaded Modules for more information.
• Gather Logs — accesses the Windows file directory where the open log files are located. Double-click to select and view an application log file.
• User Local Crash Dumps — Local crash dumps are not enabled. See Generating Crash Dumps for more information.

• Close — click to close the About box.